Two-channel relay model wireless switch

In this post I will describe a two-channel relay model wireless switch KGS-B20 from szKaige manufacturer, read my review and complete instructions how to connect and set this relay

Here are the pros and cons of Kaige 12V Remote switch with two relay

Now, read my experience with a two-channel relay circuit wireless switch, in my store I sold something about 230 units (at the time of writing this review) only 1 relay failed in 2 years – that’s great..

Here is pros

• PCB precision made, has two high-quality SONGLE relay
• It has a good reach, more than 90 meters in the open air
• is easy to set (see below in the manuals)
• A really good price, $ 4.5 to $ 5.5, even with a remote control
• Reliable service
• The circuit is in a black box
• You can connect multiple remote controls
• Has memory for saved remote controls

Here is cons

• The dial controller is a bit bigger, it could be smaller and different in color than the imitation of wood *
• the remote control is sold without a battery, you must then buy the A23 12V battery separately

*you can purchase other remote controls but they may not work

Detailed Description of Kaige two channel remote controller:

First, I’m describing the remote control – the transmitter is a brown color imitation of wood, it has two red buttons A-B (for two relays) has a telescopic antenna for a better range stretched about 5cm. Work red LED indice light while pressing the button. Operating Frequency: 315MHz but is version with 433MHz.

Receiver board has dark green color, is fitted with two independent Songle relay with 10A max switching power. each relay has three terminals:

• NO:  COM and NO contacts are open.
• COM:Basic contact most often used for power voltage.
• NC: COM and NC COM and NC contact is connected.

Other useful componets on PCB :

• Next terminals is for 12V power is for DC 12V supply, polarity – + is indicated on the rear side of the PCB
• The white button on the side of the PCB serves to pair or unset the remote controls (in the manuals I will explain how to connect the remote control with the relay)
• JP1 switch is to set the mode of operation of the relay
• The red LED indicates the signal reception

Schematic wiring diagram

useful circuits and circuits, for lighting, motors, and so on.

Great Guide manual how to pair remote controlls buttons and set receiver board mode:

Connect DC power supply 12V to receiver

Insert the 12V A23 into the remote control (if the good LED lights up on the remote control if you press the button)

Pair and unpair remote control

1. Press the white button on the receiver relay, the red LED lights up
2. Immediately press the remote control button A on the receiver, then the red LED then release, then press the B button and then the red indicator light on the receiver will blink.

Now you have a paired transmitter with a remote controller and will work as follows for button A will operate the rele 1 and the B button will control the relay 2.

Unpair remote control:

To remove the driver, press the for 8 second white button, the remote control will no longer work with the receiver (you will need to re-pair)

Set relay switching modes

The following lines provide instructions on how to set the relay switching modes. Use JP1 switch to set the desired mode Interlock,Jog,Self-locking

Interlock (hand press each key remote control, the corresponding relay is turned on, press another button on the remote control; the corresponding relay is turned on, the other off the first time only one relay is turned on,)

Self-locking, (along with a control key, press once to open, and then a close, two independent control)

JP1 has three pins 1,2,3 use a small black clutch – jumper switch here is legend how to connect pins:

• Connect pin 1 and 2: SELF-LOCK one button for one relay (first press on, second press off for each relay)
• Connect pin 2 and 3: JOG one button for one relay (hand press each key remote control, the corresponding relay connected, release the remote control button; the corresponding relay is switched off)
• Remove black jumper:Interlock mode all pins 123 is free , not connected

Here is video how to setup :

Complete technical parameters of wireless switch:

• Operating voltage: DC12V
• Working frequency: 315MHZ
• Contact capacity: ≤ 10A/250VAC; 10A/30VDC
• Receiver sensitivity:>-105dB
• Remote control distance: 50~ 100m (open area) (please stretch the antenna in order to achieve effective distance)
• Control approach: four normally open (normally closed) contacts
• Encoding type: fixed code; pad code
• Module size: 55mm × 40 mm× 20mm
• Work status: Self-locking
• Shock resistance: 270K

Remote control parameters:

• Operating voltage: DC12V
• Operating Current: ≤ 10mA
• Operating frequency: 315MHz
• Transmission Distance: 50~ 100m (open area) (please stretch the antenna in order to achieve effective distance)
• Encoding type: fixed code; pad code
• Dimensions: 51 mm× 39mm × 13.5mm
• Oscillation resistance: 4.7m

Price and buy

Dual channel remote relay wireless switch can buy from Ebay or AliExpress, good price varies around about 4-6 usd shipping included it is a very good offer considering the possibilities of use and good performance.

The only downside is that you need to buy a 12V A23 battery good price is 1usd per piece or 2.5usd in 5 pieces

FORWARDED FROM https://usefulldata.com/2-channel-remote-relay/